Quick Links. Download this manual See also: User Manual. Table of Contents. Page 2 Product warranty or service will not be extended if: 1 the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or 2 the serial number of the product is defaced or missing. Page 4 Creating a bootable floppy disk Page 5 3.
|Published (Last):||6 October 2019|
|PDF File Size:||6.38 Mb|
|ePub File Size:||16.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. Download this manual. Table of Contents. Page 2 Product warranty or service will not be extended if: 1 the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or 2 the serial number of the product is defaced or missing.
Page 3: Table Of Contents Special features Page 4 2. Page 5 Boot Settings Configuration Page 8: About This Guide Refer to the following sources for additional information and for product and software updates. Refer to the ASUS contact information. Optional documentation Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer.
Page 9: Conventions Used In This Guide Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. Page Chapter 1: Product Introduction This chapter describes the motherboard features and the new technologies it supports. Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. Page 15 See pages and for details. This protection eliminates the need to buy a replacement ROM chip.
Users will be able to play LAN games, connecting to the Internet, access and share printers, and use Skype from anywhere within range. Page Motherboard Overview Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components.
Page Motherboard Layout 1. Page 23 Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the socket. The socket alignment key should fit into Alignment key the CPU notch. Page 24 Close the load plate A , then push the load lever B until it snaps into the retention tab.
The CPU fits in only one correct orientation. Fastener Motherboard hole Make sure each fastener is oriented as shown, with the narrow groove directed outward. Page 26 Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place. Rotate each fastener counterclockwise. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard. Page 28 Remove the heatsink and fan assembly from the motherboard.
Rotate each fastener clockwise to reset the orientation. Narrow end of the groove The narrow end of the groove should point outward after resetting. The photo shows the groove shaded for emphasis. Page Installing A Dimm 1. Failure to do so may cause severe damage to both the motherboard and the components. Assign an IRQ to the card. Refer to the tables on the next page.
Install the software drivers for the expansion card. Page Interrupt Assignments 1. The figure shows a graphics card installed on the PCI Express x16 slot. Do not change the setting. Page 1. Page 40 Connect the moveable omni-directional antenna to this jack. USB 2. Page Internal Connectors Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5.
Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Page 45 This connector is for a serial COM port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis.
Remove the jumper caps only when you intend to use the chassis intrusion detection feature. Page 48 Page 50 Chapter 1: Product introduction Detailed descriptions of the BIOS parameters are also provided.
Copy the original or the latest motherboard BIOS file to the bootable floppy disk. Page Asus Ez Flash 2 Utility 2. Follow these instructions to update the BIOS using this utility.
BIN and save it to a floppy disk. The following screen appears. Page Asus Crashfree Bios 2 Utility 2. Visit the ASUS website www. Page Bios Setup Program The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen.
Page Bios Menu Screen The BIOS setup screens shown in this chapter are for reference purposes only, and may not exactly match what you see on your screen. Page Legend Bar A configurable field is enclosed in brackets, and is highlighted when selected.
Configuration options: [Disabled] [K , 3. There is a separate sub-menu for each IDE device. This is necessary so that you can write or read data from the hard disk. Make sure to set the partition of the Primary IDE hard disk drives to active.
There is a separate sub-menu for each SATA device. Configuration options: [Disabled] [Enabled] 2. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. Page Chipset [Manual]. If any of the fans is not connected to the motherboard, the field shows 0. These items are not user- configurable. Floppy Disks 1.
Floppy Disks Allows you to assign a removable drive attached to the system. Page Hard Disk Drives 2. Bootable Add-in Cards 1. Bootable Add-in Cards Allows you to assign bootable add-in cards attached to the system.
Page 85 Allows you to enable or disable the full screen logo display feature. Page Security 2. Select [System] to require the password before entering the system. Page Exit Menu Select this option only if you do not want to save the changes that you made to the Setup program. Select YES to load default values. Page Chapter 3: Software Support This chapter describes the contents of the support CD that comes with the motherboard package.
The CD automatically displays the Drivers menu if Autorun is enabled in your computer. Page Utilities Menu This utility helps you keep your computer in healthy operating condition. Click an item to open the folder of the user manual. You can also find this information on the inside front cover of this user guide. Chapter 3: Software support Page Raid Configurations Spanning does not deliver any advantage over using separate disks independently and does not provide fault tolerance or other RAID performance benefits.
Page Create Array If you want to auto-configure, proceed to the next step, otherwise, skip to step 5. The following confirmation message appears. Auto create array will destroy all data on disks, Continue? An asterisk appears before a selected drive. The data on the selected disks will Page Jmicron 3.
A write-enabled floppy disk Microsoft Windows The following screen appears, displaying the relevant information about the RAID set you created. A selected HDD shows a sign before it. A dialogue box appears to confirm the action.
Asus P5VD2 VM - SE Motherboard - Micro ATX User Manual
Asus P5VD2-VM SE User Manual – Download
Asus P5VD2-VM SE User Manual