This from a case even smaller than that of the VX-1R: 1. With its rugged die-cast aluminum chassis, the VX-2 series is built to last, and its big voice will get your transmission through! Up to 3 Watts of Power Output! Despite its compact size, the VX-2 series provides 1. And while the "Low Power" setting may be used for short-range communications, you can just touch the [F] key to engage "High" power for one transmission!

Author:Tolrajas Tygosida
Country:Turks & Caicos Islands
Language:English (Spanish)
Published (Last):7 April 2011
PDF File Size:11.99 Mb
ePub File Size:14.47 Mb
Price:Free* [*Free Regsitration Required]

Quick Links. See also: Technical Supplement. Table of Contents. International Division N. Clockwise ro- tation increases the volume level. Availability of accessories may vary. Some accessories are supplied as standard per local requirements, while others may be unavailable in some regions.

Consult your Yaesu dealer for details regarding these and any newly-available options Connection of any non-Yaesu Page 7: Installation Of Accessories Keep the dummy cover and screw in case you need to replace them in the future.

Connect the supplied Belt Clip, along with its mounting screw, to the rear panel. Do not use the Belt Clip screw to affix the dummy cover! Please be advised that the NC may contribute noise to TV and radio reception in the immediate vicinity, so we do not recommend its use adjacent to such devices.

Page Operation 3. These are the most basic steps; more advanced aspects of transmitter operation will be discussed later. The red illumination yields clear viewing of the display in a dark environment, with minimal degradation of your night vision. However, should an unusual receiving situation arise in which you need to change other receiving mode, just press the [MD] key. The receiving modes avail- able are: AUTO: Automatic mode setting per default values for the selected frequency range.

See page This can help keep your radio quiet until a specific call is received, which may be helpful while operating in congested. Your repeater system may be configured for DCS; Page Tone Calling Hz The transmitter will automatically be activated, and a Hz audio tone will be superimposed on the carrier.

Once access to the repeater has been gained, you may release the MONI key, and use the PTT key for activating the transmitter thereafter. Page 29 4. When you have made your selection, press the PTT key to save the new setting and exit to normal operation.

You may check your work by monitoring the entered callsign. Page 32 C. See page for details on setting the Home channel. Page Masking Memories VFO, although the original memory contents will remain intact on the previously-stored channel. If a Split Frequency Memory channel was transferred, the Tx frequency will be ignored you will be set up for Simplex operation on the Receive frequency.

Fortunately, the VX-2R includes provision for dividing the memories into as many as twenty Memory Banks, so you can categorize the memories in a manner convenient to you.

To return to normal operation, repeat the above power-on procedure. See page 42 regarding Memory Bank Operation for details. Page Vhf Marine Channels Page Scanning The VX-2R allows you to scan just the memory channels, the entire operating band, or a portion of that band. It will halt on signals encountered, so you can talk to the station s on that frequency, if you like. Scanning operation is basically the same in each of the above modes.

Before you begin, take a moment to select the way in which you would like the scanner to resume scanning after it halts on a signal. Page Vfo Scanning 6. If you want to change direction of the scan while it is un- derway, rotate the DIAL knob one click in the opposite direction in this case, one click counter-clockwise. To re-institute a frequency into the VFO scan loop: 1. When you have made your selection, press the PTT key to save the setting and exit to normal operation.

Page Pms Priority channel. The display will remain on the VFO or memory channel selected; When you have made your selection, press the PTT switch to save the setting and exit to normal operation. Page 57 8. To return to normal operation, just press the [ MD ] key. Smart Search is a great tool when visiting a city for the first time.

Page 59 Set Mode Item. Rotate the DIAL knob to select the desired bandwidth. Page 61 ] key, while you are transmitting, to send out the selected DTMF string to establish the link to the desired Internet-link mode.

Page Reset Procedures 2. This can be particu- larly useful when configuring a number of transceivers for a public service operation. It may be used for configuration of a wide variety of transceiver param- eters, some of which have not been detailed previously. Use the following procedure to activate the Set Mode: 1.

Page 65 Selects or disables the VFO band edge limiting for the current band. Page 69 3. Page 71 3. Page 72 Function: Selects the Reciving mode. Select the desired operating mode from the selections shown above. Page 75 or vice versa. Page Specifications 1. Page Auto" Mode Preset Operating Parameters Specifications are subject to change without notice, and are guaranteed within the and MHz amateur bands only.

Frequency ranges will vary according to transceiver version; check with your dealer. Page 79 1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 this device must accept any interference including received, interference that may cause undesired operation.

All rights reserved. Print page 1 Print document 80 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.


Yaesu VX-2 R (VX 2 R VX2R) user and service manual, modifications



Yaesu VX-2


Related Articles