Since its foundation, the company has produced single-cylinder diesel engines for industrial and construction machinery, marine applications and special applications. The company is based in Lampertheim near Mannheim , Germany. Farymann was founded on 5th August by Mr. Farny and Mr. The small business expanded very rapidly into a medium-sized company.
|Published (Last):||10 April 2012|
|PDF File Size:||6.44 Mb|
|ePub File Size:||9.11 Mb|
|Price:||Free* [*Free Regsitration Required]|
Table of contents - 2 - 1. General information, handling 5 1. Table of contents - 3 - 8. Preface - 4 - we congratulate you on your choice of a farymann engine and wish you much pleasure with this german quality product.
These operating instructions are based on the latest state of technical development. In preparing them, every effort has been made to avoid errors.
However, we accept no General information - 5 - 1. They are built as single cylinder engines vertical cylinder configuration. The direct injection guarantees an outstanding level of efficiency, with low fue General information - 6 - 1. As well as the clearly defined digit code number, this refers to the order number sn and the date of construction. This information must always be pro General information - 7 - 1.
When handling fuels, lubricants and other chemical substances, follow the safety regulations which apply to the product. General information - 8 - 1. Before you start the engine in an enclosed environment, make sure that there is sufficient ventilation.
Ensure that the engine only slows down to full stop after 10 - 20 seco Technical data - 9 - 2. Technical data engine type 15w 18w 32w design verticall number of cylinders 1 bore 75 mm 82 mm 95 mm stroke 55 mm 55 mm 74 mm cubic capacity piston displacement cm3 cm3 cm3 direction of rotation looking at power take- off side anti clockwise max.
Technical data - 10 - 2. Technical data - 11 - 2. Technical data - 12 - 2. Technical data - 13 - 2. Technical data - 15 - 2. Technical data - 16 - 2. Description use Technical data - 17 - 2. Technical data - 18 - 2. Technical data - 19 - 2. The engines have oil pressure forced lubrication. The fuel injection pump and the valves are controlled by the camshaft which is Re-assembling procedures - 20 - 3. Dismantling and assembly procedures on the basic engine 3.
Re-assembling procedures - 21 - 3. Drain lubrication oil : place suitable container under the drain hole. Remove 2 screws and cupper washers, remove oilscreen. Caution clean oilscreen carefully. Replace if any deformations or other dam- ages.
Air cleaner engines instal Re-assembling procedures - 22 - 4. Fuel lines, fuel filter remove banjo bolts, copper washers from injec- tion pump and injector.
If existing — remove fuel filter bracket, setscrews and spring washers. Close ports of injection pump and injector with banjo bolts to prevent dirt. Caution use only orig Re-assembling procedures - 23 - 5. High pressure fuel line : loosen the high pressure fuel line by holding a 14 mm wrench on the delivery valve while un- screwing the fuel line fitting.
Loosen the high pressure line at the injector in the same way. Caution check taper ends of the high pressure line Re-assembling procedures - 24 - 7. Cylinder head : remove the valve cover by removing the lock nuts and the plastic washers. If necessary tap the cover lightly with a soft faced hammer. Dis- card plastic washers and valve cover gasket. Remove the 2 locknuts and washers 1 holding the protection tub Re-assembling procedures - 25 - 8. Decompression release remove 2 screws and pull the decompression release out of the gearhousing.
Check gasket and o-seal. Replace if necessary. Caution take care not to loose the guide pin! With missing guide pin shaft will move out when engine is in operation!
Re-assembling procedures - 26 - Piston rotate the flywheel until the piston is in tdc — position. Use a needle nose plier to remove the piston pin retainer. With a drift pin gently hammer piston pin out of the piston from flywheel-side. Re-assembling procedures - 27 - Crankhandle guide remove the 2 crankhandle guide screws.
Pull of the guide in a twisting motion. Gear end cover remove the 6 allen screws and pull off the gear end cover. If necessary tap with a soft faced hammer. Caution while removing the gear end cover the g Re-assembling procedures - 28 - remove the 2 hex nuts and lock washers. Pull off the inj. If necessary turn the flywheel to decrease force from the camshaft-side. Caution leave gasket and shimson the gear end hous- ing.
Re-install hex nuts and lock washers on their studs. To remove the injecti Re-assembling procedures - 29 - Speed control assembly remove the retaining ring from the eccenter shaft using a pliers. Pull the exc.
Shaft outwards till the ratchet plate is free from the compression pin. Unhook the outer torsion spring from the boss use a pliers and watch out for your fin Re-assembling procedures - 30 - Oil pump remove the oil pump and valve bracket by un- screwing the 3 mounting screws.
Discard gasket. Flywheel remove the oil pump and valve bracket by un- screwing the 3 mounting screws. Leave the flywheel nut on the shaft. Install fly- wheel Re-assembling procedures - 31 - remove the key, belleville washers, angle ringe, o-ring and thrust washer.
Crankshaft remove the crankshaft from the crankcase, be- ing careful not to drag the crankshaft gear on the main bearing bushing. Use a puller to pull of the crankshaft gear. In case the ro Measurement table, wear - 38 - 4. Reassembly procedures - 43 - 5. Engine reassembly 1. Crankcase press the bearing bush with a suitable driver. Caution take care that the joining line of the bearing bush is located as shown and that the oil holes in the bushing and in the crankcase bore are properly linedup.
Crankshaft to install Reassembly procedures - 44 - 3. Main bearing housing press the outer race of the driver into the bear- ing cover.
15 W / 18 W
Any content, information, or advice found on social media platforms and the wider Internet, including forums such as YBW, should NOT be acted upon unless checked against a reliable, authoritative source, and re-checked, particularly where personal health and liberty is at stake. It is your responsibility to provide references to bona fide sources. Forums New posts Search forums. What's new New posts Latest activity. Log in Register.
farymann diesel 18w service manual
However, they sold the company just 5 years later to the current owner Greaves Cotton Ltd. The Farymann Marine division was established in Message me via Live Chat if don't find what you are looking for, or have old manuals to share to help other sailors. If these downloads are useful please make a donation to cover web-hosting costs and future development. Owner, Workshop and Parts Manuals are important documents that should be part of every vessel's library. They contain the detailed information necessary for safe operation, maintenance and correct servicing.
Farymann Diesel 18W Series Manuals
Table of contents - 2 - 1. General information, handling 5 1. Table of contents - 3 - 8. Preface - 4 - we congratulate you on your choice of a farymann engine and wish you much pleasure with this german quality product. These operating instructions are based on the latest state of technical development. In preparing them, every effort has been made to avoid errors. However, we accept no